FLUID MECHANICS
F1-10 Accessory
C11 MkII Pipe networks accessory - Issue 1
This freestanding accessory to the F1-10 demonstrates the characteristics of flow through different arrangements of pipes and the effect of changes in pipe diameter on the flow through a particular network.
MEASUREMENT CAPABILITIES
> Measurement of head loss versus discharge for different sizes of pipes
> Characteristics of flow through interconnected pipes of different sizes
> Characteristics of flow through parallel pipe networks
> Characteristics of flow through series pipe networks
> Application of doubling pipes on existing networks to increase flowrate
> Characteristics of flow around a ring main and the effect of changes in supplies and off-takes
Description
The permanent arrangement of PVC pipes and fittings is mounted on a freestanding support frame that is designed to stand alongside an F1-10 Hydraulics Bench in use. Connection to the F1-10 is via a reinforced flexible tube and threaded union with ‘O’ ring seal allowing connection to the F1-10 without the use of tools.
Isolating valves allow a wide range of different series, parallel and mixed pipe configurations to be created without draining the system. Flow into the network and flow out from the network at each outlet can be individually varied to change the characteristics of the system.
All clear acrylic test pipes are installed using threaded unions with ‘O’ ring seals that allow the pipes with different diameters to be repositioned without the use of tools.
Self-sealing quick release fittings at strategic points in the network allow rapid connection of the digital hand-held pressure meter, allowing appropriate differential pressures to be measured. Flow leaving any of the outlets in the network is measured using the volumetric facility incorporated on the F1-10 Hydraulics Bench.
TOPTechnical Details
Inside diameter of pipes: 14mm (1x) 10mm (1x) 9mm (2x) 6mm (1x) Differential pressure measurement: Digital pressure meter
TOPRequirements
None
TOPShipping Specification
Individual accessories on request
TOPOverall dimensions
Height: 1.380m
Width: 0.785m
Depth: 0.656m
|
 |
|---|
DATA SHEET
PRODUCT CATEGORY:
Engineering Education
F1-10 datasheetF1-10 Accessory Range:
For use in combination with the
F1-10 Hydraulics Bench
Computer aided
learning software: F1-301
Fluid Statics:
Calibrador de manómetro de peso muerto: F1-11
Fluid statics & manometry apparatus: F1-29
Fluid properties apparatus: F1-30
Fluid Dynamics:
Demostración del Teorema de Bernoulli : F1-15
Descarga por orificios y trayectoria de chorro libre : F1-17
Descarga por orificios: F1-17a
Pérdidas de carga en tuberías: F1-18
Demostración de
Osborne Reynolds : F1-20
Demostración y comparación de caudalímetros: F1-21
Pérdidas de carga
en acodamientos : F1-22
Vórtices libres y forzados: F1-23
Equipo para
demostrar Cavitación: F1-28
Mediciones de fricción
de fluido: C6MkII-10
Pipe surge and water hammer apparatus: C7MkII
Pipe networks accessory: C11MkII
Hydraulic Flow Demonstrator: S16
Open Channel Flow:
Canal Hidraulico
multipropósito: C4MkII
Hydraulic Flow Demonstrator: S16
Rotodynamic Machines:
Demonstration Pelton turbine:F1-25
Centrifugal pump
characteristics: F1-27
Demonstration Francis turbine: F1-32
Equipo Complementario
Calibrador de manómetro de precisión: F4
Aparato de Osborne Reynolds: F5
Banco de propiedades de fluidos e hidrostática: F9092
Equipo Para Demostrar Cavitación: F1-28
Coeficientes de arrastre de partículas: F12
Visualizador de flujo por burbujas de hidrógeno: F14MkII